JavaScript is disabled for your browser. Some features of this site may not work without it.
Navegação IPEN por Autores IPEN "MUCSI, CRISTIANO S."
-
MARCELO, LARISSA A.
; ROSSI, JESUALDO L.
; LARA, JOSE A.C.
; MUCSI, CRISTIANO S.
.
Analysis of Resistance Spot Welding (RSW) on 22MnB5 material after hot stamping for automotive applications (B-pillar).
In: SIMPÓSIO INTERNACIONAL DE ENGENHARIA AUTOMOTIVA, 28th,
March 17-18, 2021,
Online.
Proceedings...
São Paulo, SP: Blucher,
2021.
p. 157-161.
DOI:
10.5151/simea2021-PAP37
Abstract:
One of the major concerns that arose in recent years
within the automotive industry has been making cars
sustainable, safe and economic. One of the ways to solve
this equation is to use lighter materials that reduce the
weight of vehicles and increase the energy absorption
mainly on the B-pillar. This paper aims to study the RSW
cycle of the welding parameter known as P1. The parameter
were defined to reach the maximum load during the tensile
test according to the norm AWS D8.9. The test samples
were assembled with a GAP to reproduce real vehicle
welding conditions, and the parameter P1 weld 22MnB5
steel samples with heat treatment, known as Press
Hardening Steel (PHS). The influence of these parameters
on the PHS mechanical properties was evaluated with
Vickers hardness test (HV), metallographic technique,
conducting ultrasonic and tensile test. The results
confirmed the difference at the Heat affected zone (HAZ)
mechanical strength over fusion zone. It was possible to
visualize a softening region in the HAZ and increasing to
the weld point, which is demonstrated in the microstructural
analysis and thus justifies the detachment of the weld
button of the base material in tensile test. Keywords: PHS,
HAZ, RSW.
MARCELO, LARISSA A.; ROSSI, JESUALDO L.; LARA, JOSE A.C.; MUCSI, CRISTIANO S.
Analysis of Resistance Spot Welding (RSW) on 22MnB5 material after hot stamping for automotive applications (B-pillar).
In:
SIMPÓSIO INTERNACIONAL DE ENGENHARIA AUTOMOTIVA, 28th,
March 17-18, 2021,
Online.
Proceedings...
São Paulo, SP: Blucher,
2021.
p. 157-161.
DOI:
10.5151/simea2021-PAP37.
Disponível em: http://repositorio.ipen.br/handle/123456789/33550. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
MICELLI, ANA L.P.
; NIGRO, FREDERICO
; MUCSI, CRISTIANO S.
; ALENCAR, MAICON C. de
; ARANHA, LUIS C.
; ROSSI, JESUALDO L.
.
Analysis of the pullout testing of straight and angled abutments in narrow diameter implants.
Materials Science Forum,
v. 1012,
p. 461-465,
2020.
DOI:
10.4028/www.scientific.net/MSF.1012.461
Abstract:
Despite the success of osseointegrated implants, some biomechanical problems such as
loosening or fracture of the abutment, crown fixation screw loosening and prosthetic instability, are
common problems reported in the literature. Thus, the objective of the present study was to analyze
the pullout resistance of straight and angled abutments in narrow diameter implants installed by
means of friction. The specimen was composed of an implant of 3.3 mm x 11 mm fixed 2 mm above
of a resin block. The abutments were fixed by friction receiving 3, 5 and 7 strikes of 0.05 J along the
implant axis, and were positioned with 0˚, 10˚ and 20˚ of angulation. The abutments were subjected
to pullout load, totalizing 10 repetitions for each test, i.e., the abutment was reinserted up to 10 times
in the same implant. The results showed higher values of pullout load for the abutments with 7 strikes,
and no statistical difference with 5 strikes suggesting better mechanical stability.
Palavras-Chave:
implants;
dentistry;
bone tissues;
testing;
prostheses;
teeth;
extraction;
connectors
MICELLI, ANA L.P.; NIGRO, FREDERICO; MUCSI, CRISTIANO S.; ALENCAR, MAICON C. de; ARANHA, LUIS C.; ROSSI, JESUALDO L.
Analysis of the pullout testing of straight and angled abutments in narrow diameter implants.
Materials Science Forum,
v. 1012,
p. 461-465,
2020.
DOI:
10.4028/www.scientific.net/MSF.1012.461.
Disponível em: http://repositorio.ipen.br/handle/123456789/31828. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
GOMES, MAURILIO P.
; SANTOS, IGOR P. dos
; REIS, LUIS A.M. dos
; COUTO, CAMILA P.
; MUCSI, CRISTIANO S.
; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
.
Characterization of sintered valve seat inserts obtained with AISI M2 high-speed steel after air quenching / Caracterização de insertos para assentos de válvulas sinterizados obtidos com o aço rápido AISI M2 depois de temperados ao ar.
In: ABM WEEK; CONGRESSO ANUAL DA ABM, 72.; ENCONTRO NACIONAL DE ESTUDANTES DE ENGENHARIA METALURGICA, DE MATERIAIS E DE MINAS, 17.,
02-06 de outubro, 2017,
São Paulo, SP.
Anais...
São Paulo, SP: Associação Brasileira de Metalurgia, Materiais e Mineração,
2017.
p. 993-1000.
Abstract:
The aim of this work was to heat treat and characterize sintered valve seat inserts (VSI). The powder metallurgy route was the only way found to substitute cobalt and lead, used in the VSI original alloy, due to their high cost and toxicological effect, respectively. The studied VSI was obtained with AISI M2 high-speed steel powder mixed with iron powder and other additives such as manganese sulphide, graphite, zinc stearate, carbides and copper, which was added by metallic infiltration. All the VSI were air quenched and double tempered, for one hour each, at seven different equidistantly temperatures, ranging from 100 °C up to 700 °C. The physical and mechanical properties were evaluated by means of the VSI apparent density, apparent hardness and crush radial strength. The chemical composition was determined through gas analysis, for the light elements such as carbon and sulfur, and energy dispersive X-ray fluorescence spectrometry for other elements. Microstructural characterization was performed with the support of scanning electron microscopy and energy dispersive spectroscopy. Regarding the VSI final application, the best results were achieved with the inserts air quenched and double tempered at 600 °C.
Palavras-Chave:
heat treatments;
powder metallurgy;
steels;
valves;
air;
quenching
GOMES, MAURILIO P.; SANTOS, IGOR P. dos; REIS, LUIS A.M. dos; COUTO, CAMILA P.; MUCSI, CRISTIANO S.; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
Characterization of sintered valve seat inserts obtained with AISI M2 high-speed steel after air quenching.
In:
ABM WEEK; CONGRESSO ANUAL DA ABM, 72.; ENCONTRO NACIONAL DE ESTUDANTES DE ENGENHARIA METALURGICA, DE MATERIAIS E DE MINAS, 17.,
02-06 de outubro, 2017,
São Paulo, SP.
Anais...
São Paulo, SP: Associação Brasileira de Metalurgia, Materiais e Mineração,
2017.
p. 993-1000.
Disponível em: http://repositorio.ipen.br/handle/123456789/31174. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
SATO, IVONE M.
; PEREIRA, LUIZ A.T.; SCAPIN, MARCOS A.
; COTRIM, MARYCEL B.
; MUCSI, CRISTIANO S.
; ROSSI, JESUALDO L.
; MARTINEZ, LUIS G.
.
Chemical and microstructural characterization of remelted zircaloy by X-ray fluorescence techniques and metallographic analysis.
Journal of Radioanalytical and Nuclear Chemistry,
v. 294,
n. 2,
p. 283-288,
2012.
Palavras-Chave:
zircaloy;
x-ray fluorescence analysis;
microstructure;
hafnium;
interfering elements
SATO, IVONE M.; PEREIRA, LUIZ A.T.; SCAPIN, MARCOS A.; COTRIM, MARYCEL B.; MUCSI, CRISTIANO S.; ROSSI, JESUALDO L.; MARTINEZ, LUIS G.
Chemical and microstructural characterization of remelted zircaloy by X-ray fluorescence techniques and metallographic analysis.
Journal of Radioanalytical and Nuclear Chemistry,
v. 294,
n. 2,
p. 283-288,
2012.
Disponível em: http://repositorio.ipen.br/handle/123456789/4318. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
NOGUEIRA, EDUARDO J.
; ROSSI, JESUALDO L.
; MUCSI, CRISTIANO S.
.
Desenvolvimento de tecnologia e dispositivo para a medicao de torque de fixação de elementos roscados.
In: PROGRAMA INSTITUCIONAL DE BOLSAS DE INICIAÇÃO CIENTÍFICA, 20.; PROGRAMA DE BOLSAS E INICIAÇÃO CIENTÍFICA CNEN, 11.; PROGRAMA INSTITUCIONAL DE BOLSAS DE INICIAÇÃO DESENVOLVIMENTO TECNOLÓGICO E INOVAÇÃO, 4.,
22-23 de outubro, 2014,
São Paulo, SP.
Resumo expandido...
2014.
p. 106-107.
Palavras-Chave:
commercialization;
equipment;
torque;
fastening;
strain gages
NOGUEIRA, EDUARDO J.; ROSSI, JESUALDO L.; MUCSI, CRISTIANO S.
Desenvolvimento de tecnologia e dispositivo para a medicao de torque de fixação de elementos roscados.
In:
PROGRAMA INSTITUCIONAL DE BOLSAS DE INICIAÇÃO CIENTÍFICA, 20.; PROGRAMA DE BOLSAS E INICIAÇÃO CIENTÍFICA CNEN, 11.; PROGRAMA INSTITUCIONAL DE BOLSAS DE INICIAÇÃO DESENVOLVIMENTO TECNOLÓGICO E INOVAÇÃO, 4.,
22-23 de outubro, 2014,
São Paulo, SP.
Resumo expandido...
2014.
p. 106-107.
Disponível em: http://repositorio.ipen.br/handle/123456789/25998. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
MUCSI, CRISTIANO S.
; NOGUEIRA, EDUARDO J.; ARANHA, LUIS C.
; CEONI, FRANCISCO C.
; JESUS, EDILSON R.B. de; ROSSI, JESUALDO L.
.
Desenvolvimentos de tecnolgia e dispositivo para a medição de torque de fixação de elementos roscados.
In: CONGRESSO CIENTITÍFICO DA SEMANA TECNOLÓGICA, 5.,
20-24 de outubro, 2014,
Bragança Paulista, SP.
Anais...
2014.
Palavras-Chave:
technology development;
torque;
implants;
teeth;
equipment;
measuring instruments
MUCSI, CRISTIANO S.; NOGUEIRA, EDUARDO J.; ARANHA, LUIS C.; CEONI, FRANCISCO C.; JESUS, EDILSON R.B. de; ROSSI, JESUALDO L.
Desenvolvimentos de tecnolgia e dispositivo para a medição de torque de fixação de elementos roscados.
In:
CONGRESSO CIENTITÍFICO DA SEMANA TECNOLÓGICA, 5.,
20-24 de outubro, 2014,
Bragança Paulista, SP.
Anais...
2014.
Disponível em: http://repositorio.ipen.br/handle/123456789/26341. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
TODESCO, SERGIO R.
; MUCSI, CRISTIANO S.
; ROSSI, JESUALDO L.
.
Design of a test device for subjecting materials to high strain rates with application in nuclear area.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Palavras-Chave:
strain rate;
materials testing;
impact tests;
deformation;
design;
equipment;
lagrangian function;
stress analysis
TODESCO, SERGIO R.; MUCSI, CRISTIANO S.; ROSSI, JESUALDO L.
Design of a test device for subjecting materials to high strain rates with application in nuclear area.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Disponível em: http://repositorio.ipen.br/handle/123456789/25135. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ARANHA, LUIS C.
; MUCSI, CRISTIANO S.
; CEONI, FRANCISCO C.
; NOGUEIRA, EDUARDO J.
; ROSSI, JESUALDO L.
.
Dispositivo para o estudo do comportamento do microtorque na fixação in vitro de pilar protético.
ImplantNewsPerio International Journal,
v. 12,
n. 6,
p. 181-186,
2015.
Palavras-Chave:
torque;
implants;
extensometers;
dentistry;
comparative evaluations;
prostheses;
in vitro
ARANHA, LUIS C.; MUCSI, CRISTIANO S.; CEONI, FRANCISCO C.; NOGUEIRA, EDUARDO J.; ROSSI, JESUALDO L.
Dispositivo para o estudo do comportamento do microtorque na fixação in vitro de pilar protético.
ImplantNewsPerio International Journal,
v. 12,
n. 6,
p. 181-186,
2015.
Disponível em: http://repositorio.ipen.br/handle/123456789/26573. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
BETINI, EVANDRO G.
; GOMES, MAURILIO P.
; MUCSI, CRISTIANO S.
; ORLANDO, MARCOS T.D.; LUZ, TEMISTOCLES de S.; AVETTAND-FENOEL, MARIE-NOELLE; ROSSI, JESUALDO L.
.
Effect of nitrogen addition to shielding gas on cooling rates and in the microstructure of thin sheets of duplex stainless steel welded by pulsed gas tungsten arc welding process.
Materials Research,
v. 22,
1,
p. 1-9,
2019.
DOI:
10.1590/1980-5373-MR-2019-0247
Abstract:
The effect of the nitrogen content in the shielding gas and its effect on temperature distributions
at the welded zone of thin sheets of duplex stainless steel have been evaluated. The duplex stainless
steels have many features due to unique microstructural combination of austenite and ferrite grains.
The phase balance can be easily shifted depending on the welding parameters. Two sheets were
welded using pure argon and pure argon plus 2% of nitrogen as shielding gas. The thermal profile had
shown that N2-supplemented shielding gas lead to higher peaks of temperature using similar welding
parameters. Microstructural examination showed that the austenite phase in the weld increased with the
presence of nitrogen in the shielding gas. The added nitrogen promoted primary austenite formation and
slightly increases the microhardness at the solidified zone. Microhardness mapping and metallographic
imaging presented information about microstructures, confirming the formation of secondary phases
during thermal cycle in the temperature range 850 °C and 950 °C. Control of ferrite amounts in the
welds is essential mainly to improve mechanical properties and corrosion resistance of welding zones.
Palavras-Chave:
nitrogen;
stainless steels;
steels;
cooling;
gas tungsten-arc welding;
thermal cycling;
microhardness;
microstructure
BETINI, EVANDRO G.; GOMES, MAURILIO P.; MUCSI, CRISTIANO S.; ORLANDO, MARCOS T.D.; LUZ, TEMISTOCLES de S.; AVETTAND-FENOEL, MARIE-NOELLE; ROSSI, JESUALDO L.
Effect of nitrogen addition to shielding gas on cooling rates and in the microstructure of thin sheets of duplex stainless steel welded by pulsed gas tungsten arc welding process.
Materials Research,
v. 22,
p. 1-9,
2019.
1,
DOI:
10.1590/1980-5373-MR-2019-0247.
Disponível em: http://repositorio.ipen.br/handle/123456789/30422. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
MUCSI, CRISTIANO S.
.
Estudo sobre o processo V.A.R. (Vacuum Arc Remelting) escala de laboratorio.
1996.
Dissertacao (Mestrado) -
Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP,
Sao Paulo.
156 p.
Orientador: Arnaldo Homobono Paes de Andrade.
Palavras-Chave:
electric arcs;
melting;
refining;
refractories;
alloys;
bench-scale experiments
MUCSI, CRISTIANO S.
Estudo sobre o processo V.A.R. (Vacuum Arc Remelting) escala de laboratorio.
Orientador: Arnaldo Homobono Paes de Andrade.
1996.
156 f.
Dissertacao (Mestrado) -
Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP,
Sao Paulo.
Disponível em: http://repositorio.ipen.br/handle/123456789/10472. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
GOMES, MAURILIO P.
; SANTOS, IGOR P. dos
; COUTO, CAMILA P.
; BETINI, EVANDRO G.
; REIS, LUIS A.M. dos
; MUCSI, CRISTIANO S.
; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
.
Heat treatment of sintered valve seat inserts.
Materials Research,
v. 21,
n. 5,
2018.
DOI:
10.1590/1980-5373-MR-2018-0068
Abstract:
The characterization of sintered valve seat inserts (VSIs) after being subjected to different heat
treatment operations has been carried out. The VSIs were obtained from three different alloys by mixing
iron powder with AISI M3:2, AISI M2 high-speed steels, and AISI D2 tool steel. After sintering, the VSI
were quenched in air followed by double tempering at seven different temperatures. The cooling rate
during air quenching was measured by means of a thermocouple type k attached to a data acquisition
system. The characterization of the mechanical and physical properties of the VSIs was achieved by
measuring relative density, apparent hardness and crush radial strength. The resulting microstructures
for the sintered parts were interpreted using the isothermal and continuous cooling transformation
diagrams for similar alloys. The VSI obtained with AISI M3:2 and AISI M2 high-speed steels after
air quenching and double tempering at 600 ºC showed the best results in terms of apparent hardness
and crush radial strength.
Palavras-Chave:
powder metallurgy;
sintering;
heat treatments;
valves;
steels
GOMES, MAURILIO P.; SANTOS, IGOR P. dos; COUTO, CAMILA P.; BETINI, EVANDRO G.; REIS, LUIS A.M. dos; MUCSI, CRISTIANO S.; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
Heat treatment of sintered valve seat inserts.
Materials Research,
v. 21,
n. 5,
2018.
DOI:
10.1590/1980-5373-MR-2018-0068.
Disponível em: http://repositorio.ipen.br/handle/123456789/29307. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
MORAIS, NATHANAEL W.S.
; MUCSI, CRISTIANO S.
; FABRIM, ZACARIAS E.
; SCHON, CLAUDIO G.; ROSSI, JESUALDO L.
.
Microstructural characterization of U-7.5Nb-2.5Zr alloy after ageing and constrained fatigue.
Materials Research,
v. 26,
Suppl.1,
p. 1-6,
2023.
DOI:
10.1590/1980-5373-MR-2023-0039
Abstract:
U-7.5Nb-2.5Zr cladded in Zircaloy-4 is one of the most studied fuel prototypes. The Nb and Zrare added to the U to stabilize the body-centered cubic (BCC) gamma phase and grant mechanical and swelling resistance. The U-7.5Nb-2.5Zr undergoes the gamma to α′′ phase transformation, generating compressive stresses due to the volume reduction. The α′′ phase also can transform to a combination of α + γ2 phase (equilibrium phases), which are known to be hard and brittle. This work had the objective to test the effect of ageing the gamma to α′′ phase in thermal cycling of a U-7.5Nb-2.5Zr cladded in Zircaloy-4 part. A co-laminated specimen was aged and thermally cycled in a dilatometry experiment. The samples were characterized through X-ray diffraction and metallography. The results show that the gamma to α′′ phase transformations occur at the begin- ning of the initial ageing, followed by stress relief. During the cycling, the sample demonstrated non-equal thermal strains and presented fractures along with the U matrix.
MORAIS, NATHANAEL W.S.; MUCSI, CRISTIANO S.; FABRIM, ZACARIAS E.; SCHON, CLAUDIO G.; ROSSI, JESUALDO L.
Microstructural characterization of U-7.5Nb-2.5Zr alloy after ageing and constrained fatigue.
Materials Research,
v. 26,
p. 1-6,
2023.
Suppl.1,
DOI:
10.1590/1980-5373-MR-2023-0039.
Disponível em: http://repositorio.ipen.br/handle/123456789/34363. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
LEITE, DANIELA M.C.
; ALENCAR, MAICON C. de
; MUCSI, CRISTIANO S.
; ARAUJO, JOAO V.S.
; TAVARES, LUIZ A.
; BERBEL, LARISSA O.
; ARANHA, LUIS C.
; ROSSI, JESUALDO L.
.
Modifications of titanium and zirconium alloy surfaces for use as dental implants.
Materials Science Forum,
v. 1012,
p. 477-482,
2020.
DOI:
10.4028/www.scientific.net/MSF.1012.477
Abstract:
The use of dental implants of titanium and its alloys has proved to be effective, through
well established and documented parameters, both in the dimensions and in the manufacturing
processes and also in the surgical techniques. There are clinical situations where there is a need to
reduce the diameter of the implants, below 3.75 mm in diameter. In the current state of art of the
implant technology it is desirable that these also have surfaces capable of decreasing the period of
osseointegration. In the present work, to improve the mechanical strength of the material, an alloy
of 80% of Ti and 20% of Zr % in mass was proposed and elaborated, aiming its use as biomaterial.
Physical, chemical, microstructural and mechanical characterization was carried out. The surfaces
of the treated samples were observed using: scanning electron microscopy (SEM); semi
quantitatively chemically analyzed using dispersive energy spectroscopy (EDS: wettability of the
samples was determined and, finally, the roughness was measured using optical profilometry. For
the conditions used in the present work, it was concluded, that the best surface treatment for the
TiZr 80/20 alloy was acid etching with 1% vol. hydrofluoric acid for 5 minutes, as this treatment
presented the most prominent results of wettability and roughness simultaneously.
Palavras-Chave:
titanium;
zirconium;
alloys;
implants;
dentistry;
biological materials;
melting;
scanning electron microscopy;
spectroscopy;
energy;
dispersion relations;
bone tissues
LEITE, DANIELA M.C.; ALENCAR, MAICON C. de; MUCSI, CRISTIANO S.; ARAUJO, JOAO V.S.; TAVARES, LUIZ A.; BERBEL, LARISSA O.; ARANHA, LUIS C.; ROSSI, JESUALDO L.
Modifications of titanium and zirconium alloy surfaces for use as dental implants.
Materials Science Forum,
v. 1012,
p. 477-482,
2020.
DOI:
10.4028/www.scientific.net/MSF.1012.477.
Disponível em: http://repositorio.ipen.br/handle/123456789/31829. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
PEREIRA, LUIZ A.T.
; MARTINEZ, LUIS G.
; MUCSI, CRISTIANO S.
; REIS, LUIS A.M. dos
; ROSSI, JESUALDO L.
.
On the melting of zirconium alloys from scraps using electron beam and induction furnaces: recycling process viability.
Journal of Materials Research and Technology,
v. 9,
n. 3,
p. 4867-4875,
2020.
DOI:
10.1016/j.jmrt.2020.03.006
Abstract:
The pressurized water reactor (PWR) employs UO2pellets as nuclear fuel, which are packedin zirconium alloy tubes called nuclear fuel cladding. In the manufacture of the nuclearfuel, machining scraps are generated which are not easily discarded as scraps because ofits high cost. These zirconium nuclear alloys are very costly and are not produced in Brazil.In this work, novel methods to recycle Zircaloy scraps using vacuum induction melting andelectron beam furnaces were used to obtain ingots. The cast ingots were subjected to ther-mal treatments and then chemically analyzed, followed by microstructural characterization,mechanical properties evaluation, and X-ray diffraction. The results indicated the feasibilityof the processes for obtaining alloys for application in the nuclear area, chemical industryor materials for biological applications such as dental prostheses.
Palavras-Chave:
electron beams;
zirconium alloys;
recycling;
reactors;
nuclear fuels;
cladding;
induction;
microstructure
PEREIRA, LUIZ A.T.; MARTINEZ, LUIS G.; MUCSI, CRISTIANO S.; REIS, LUIS A.M. dos; ROSSI, JESUALDO L.
On the melting of zirconium alloys from scraps using electron beam and induction furnaces: recycling process viability.
Journal of Materials Research and Technology,
v. 9,
n. 3,
p. 4867-4875,
2020.
DOI:
10.1016/j.jmrt.2020.03.006.
Disponível em: http://repositorio.ipen.br/handle/123456789/31403. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
-
REIS, LUIS A.M. dos
; MUCSI, CRISTIANO S.
; TAVARES, LUIZ A.P.
; ALENCAR, MAICON C.
; GOMES, MAURILIO P.
; BARBOSA, LUZINETE P.
; ROSSI, JESUALDO L.
.
Recycling and melting process of the zirconium alloy chips.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Palavras-Chave:
cleaning;
electrodes;
enriched uranium;
fuel rods;
melting;
pwr type reactors;
quality control;
recycling;
scrap;
uranium 235;
vacuum furnaces;
zirconium alloys
REIS, LUIS A.M. dos; MUCSI, CRISTIANO S.; TAVARES, LUIZ A.P.; ALENCAR, MAICON C.; GOMES, MAURILIO P.; BARBOSA, LUZINETE P.; ROSSI, JESUALDO L.
Recycling and melting process of the zirconium alloy chips.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/28362. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
BETINI, EVANDRO G.
; CEONI, FRANCISCO C.
; MUCSI, CRISTIANO S.
; POLITANO, RODOLFO
; ROSSI, JESUALDO L.
; ORLANDO, MARCOS T.D..
Study of the temperature distribution on welded thin plates duplex steel to be used for the external clad of a cask for transportation of radiopharmaceuticals products.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Palavras-Chave:
temperature distribution;
ambient temperature;
plates;
steels;
casks;
radiation transport;
radiopharmaceuticals
BETINI, EVANDRO G.; CEONI, FRANCISCO C.; MUCSI, CRISTIANO S.; POLITANO, RODOLFO; ROSSI, JESUALDO L.; ORLANDO, MARCOS T.D.
Study of the temperature distribution on welded thin plates duplex steel to be used for the external clad of a cask for transportation of radiopharmaceuticals products.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Disponível em: http://repositorio.ipen.br/handle/123456789/23995. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
BETINI, EVANDRO G.
; GOMES, MAURILIO P.
; MUCSI, CRISTIANO S.
; LUZ, TEMISTOCLES de S.; ORLANDO, MARCOS T.D.; ROSSI, JESUALDO L.
.
Study of the thermal diffusivity variation in thin duplex steel plates welded by GTAW process.
Materials Science Forum,
v. 930,
p. 460-465,
2018.
DOI:
10.4028/www.scientific.net/MSF.930.460
Abstract:
This study describes the thermal diffusivity of thin duplex steel plates in the thickness
direction measured using the laser-flash method after welding. The work reports the experimental
efforts in recording temperature profiles of the grade UNS S32304 duplex steel during autogenous
welding. The butt weld autogenous joints were carried out by the GTAW (gas tungsten arc welding)
process with either argon or argon - 2% nitrogen atmospheres. The amount of nitrogen in the heat
affected regions, after welding, was measured and correlated with the variation of the thermal
diffusivity of the studied material. The temperature profiles were obtained using k-type
thermocouples connected to a digital data acquisition system. Different thermal cycles and thermal
diffusivity values were observed in the heat-affected zone (HAZ) for both samples. In the solidified
zone (SZ) was observed similar increase of the thermal diffusivity values for the plates welded with
pure argon and argon plus nitrogen atmosphere.
Palavras-Chave:
argon;
gas tungsten-arc welding;
heat affected zone;
microstructure;
nitrogen;
plates;
steels;
temperature distribution;
thermal diffusivity
BETINI, EVANDRO G.; GOMES, MAURILIO P.; MUCSI, CRISTIANO S.; LUZ, TEMISTOCLES de S.; ORLANDO, MARCOS T.D.; ROSSI, JESUALDO L.
Study of the thermal diffusivity variation in thin duplex steel plates welded by GTAW process.
Materials Science Forum,
v. 930,
p. 460-465,
2018.
DOI:
10.4028/www.scientific.net/MSF.930.460.
Disponível em: http://repositorio.ipen.br/handle/123456789/29273. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
BETINI, EVANDRO G.
; GOMES, MAURILIO P.
; MILAGRE, MARIANA X.
; MACHADO, CARULINE S.C.
; REIS, LUIS A.M.
; MUCSI, CRISTIANO S.
; ORLANDO, MARCOS T.D.; LUZ, TEMISTOCLES S.; ROSSI, JESUALDO L.
.
Study on welding thermal cycle and residual stress of UNS S32304 duplex steel selected as external shield for a transport packaging of Mo-99.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Palavras-Chave:
containers;
gas tungsten-arc welding;
molybdenum 99;
nitrogen;
residual stresses;
stainless steels;
temperature range 0400-1000 k;
thermal cycling
BETINI, EVANDRO G.; GOMES, MAURILIO P.; MILAGRE, MARIANA X.; MACHADO, CARULINE S.C.; REIS, LUIS A.M.; MUCSI, CRISTIANO S.; ORLANDO, MARCOS T.D.; LUZ, TEMISTOCLES S.; ROSSI, JESUALDO L.
Study on welding thermal cycle and residual stress of UNS S32304 duplex steel selected as external shield for a transport packaging of Mo-99.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/28359. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
GOMES, MAURILIO P.
; SANTOS, IGOR P. dos
; COUTO, CAMILA P.
; MUCSI, CRISTIANO S.
; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
.
Têmpera ao ar de insertos de assentos de válvulas obtidos com aço ferramenta AISI D2.
In: CONFERENCIA BRASILEIRA SOBRE TEMAS DE TRATAMENTO TERMICO, 8.,
21-24 de maio, 2017,
Indaiatuba, SP.
Anais...
2017.
Abstract:
A obtenção de insertos de assentos de válvulas por metalurgia de pó usando uma mistura de
pó de ferro e aços rápidos ou aços ferramenta está atendendo os requisitos para a
substituição do cobalto e chumbo em peças comerciais, visando a redução de custo e
evitando a toxicidade do chumbo. O objetivo do presente trabalho foi o de tratar
termicamente e caracterizar os insertos de assentos de válvulas sinterizados obtidos
utilizando-se uma mistura de pós. Essa mistura de pós foi constituída pelo aço ferramenta
AISI D2, ferro, sulfato de manganês, carboneto de nióbio, grafite, estearato de zinco e cobre.
O ciclo de temperatura da têmpera ao ar foi determinado por meio do termopar tipo k
acoplado a um sistema de aquisição de dados. As propriedades físicas e mecânicas foram
medidas em relação à dureza aparente dos insertos, densidade aparente e a sua resistência à
ruptura radial. A caracterização microestrutural foi realizada utilizando-se a microscopia
óptica, microscopia eletrônica de varredura e espectroscopia por dispersão de energia. Os
insertos temperados ao ar e duplamente revenido a 500 °C mostraram os melhores resultados
no que tange a dureza e resistência à ruptura radial.
Palavras-Chave:
sintered materials;
valves;
machining;
powder metallurgy;
heat treatments
GOMES, MAURILIO P.; SANTOS, IGOR P. dos; COUTO, CAMILA P.; MUCSI, CRISTIANO S.; COLOSIO, MARCO A.; ROSSI, JESUALDO L.
Têmpera ao ar de insertos de assentos de válvulas obtidos com aço ferramenta AISI D2.
In:
CONFERENCIA BRASILEIRA SOBRE TEMAS DE TRATAMENTO TERMICO, 8.,
21-24 de maio, 2017,
Indaiatuba, SP.
Anais...
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/29235. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
Buscar no repositório
Navegar
-
Todo o repositório
-
Esta comunidade
Minha conta
Visualizar
A pesquisa no RD utiliza os recursos de busca da maioria das bases de dados. No entanto algumas dicas podem auxiliar para obter um resultado mais pertinente.
✔ É possível efetuar a busca de um autor ou um termo em todo o RD, por meio do
Buscar no Repositório
, isto é, o termo solicitado será localizado em qualquer campo do RD. No entanto esse tipo de pesquisa não é recomendada a não ser que se deseje um resultado amplo e generalizado.
✔ A pesquisa apresentará melhor resultado selecionando um dos filtros disponíveis em
Navegar
✔ Os filtros disponíveis em
Navegar
tais como: Coleções, Ano de publicação, Títulos, Assuntos, Autores, Revista, Tipo de publicação são autoexplicativos. O filtro,
Autores IPEN
apresenta uma relação com os autores vinculados ao IPEN; o
ID Autor IPEN
diz respeito ao número único de identificação de cada autor constante no RD e sob o qual estão agrupados todos os seus trabalhos independente das variáveis do seu nome;
Tipo de acesso
diz respeito à acessibilidade do documento, isto é , sujeito as leis de direitos autorais, ID RT apresenta a relação dos relatórios técnicos, restritos para consulta das comunidades indicadas.
A opção
Busca avançada
utiliza os conectores da lógica boleana, é o melhor recurso para combinar chaves de busca e obter documentos relevantes à sua pesquisa, utilize os filtros apresentados na caixa de seleção para refinar o resultado de busca. Pode-se adicionar vários filtros a uma mesma busca.
Exemplo:
Buscar os artigos apresentados em um evento internacional de 2015, sobre loss of coolant, do autor Maprelian.
Autor: Maprelian
Título: loss of coolant
Tipo de publicação: Texto completo de evento
Ano de publicação: 2015
✔ Para indexação dos documentos é utilizado o Thesaurus do INIS, especializado na área nuclear e utilizado em todos os países membros da
International Atomic Energy Agency – IAEA
, por esse motivo, utilize os termos de busca de assunto em inglês; isto não exclui a busca livre por palavras, apenas o resultado pode não ser tão relevante ou pertinente.
✔ 95% do RD apresenta o texto completo do documento com livre acesso, para aqueles que apresentam o significa que e o documento está sujeito as leis de direitos autorais, solicita-se nesses casos contatar a Biblioteca do IPEN,
bibl@ipen.br
.
✔ Ao efetuar a busca por um autor o RD apresentará uma relação de todos os trabalhos depositados no RD. No lado direito da tela são apresentados os coautores com o número de trabalhos produzidos em conjunto bem como os assuntos abordados e os respectivos anos de publicação agrupados.
✔ O RD disponibiliza um quadro estatístico de produtividade, onde é possível visualizar o número dos trabalhos agrupados por tipo de coleção, a medida que estão sendo depositados no RD.
✔ Na página inicial nas referências são sinalizados todos os autores IPEN, ao clicar nesse símbolo será aberta uma nova página correspondente à aquele autor – trata-se da página do pesquisador.
✔ Na página do pesquisador, é possível verificar, as variações do nome, a relação de todos os trabalhos com texto completo bem como um quadro resumo numérico; há links para o Currículo Lattes e o Google Acadêmico ( quando esse for informado).
ATENÇÃO!
ESTE TEXTO "AJUDA" ESTÁ SUJEITO A ATUALIZAÇÕES CONSTANTES, A MEDIDA QUE NOVAS FUNCIONALIDADES E RECURSOS DE BUSCA FOREM SENDO DESENVOLVIDOS PELAS EQUIPES DA BIBLIOTECA E DA INFORMÁTICA.
O gerenciamento do Repositório está a cargo da Biblioteca do IPEN. Constam neste RI, até o presente momento 20.950 itens que tanto podem ser artigos de periódicos ou de eventos nacionais e internacionais, dissertações e teses, livros, capítulo de livros e relatórios técnicos. Para participar do RI-IPEN é necessário que pelo menos um dos autores tenha vínculo acadêmico ou funcional com o Instituto. Nesta primeira etapa de funcionamento do RI, a coleta das publicações é realizada periodicamente pela equipe da Biblioteca do IPEN, extraindo os dados das bases internacionais tais como a Web of Science, Scopus, INIS, SciElo além de verificar o Currículo Lattes. O RI-IPEN apresenta também um aspecto inovador no seu funcionamento. Por meio de metadados específicos ele está vinculado ao sistema de gerenciamento das atividades do Plano Diretor anual do IPEN (SIGEPI). Com o objetivo de fornecer dados numéricos para a elaboração dos indicadores da Produção Cientifica Institucional, disponibiliza uma tabela estatística registrando em tempo real a inserção de novos itens. Foi criado um metadado que contém um número único para cada integrante da comunidade científica do IPEN. Esse metadado se transformou em um filtro que ao ser acionado apresenta todos os trabalhos de um determinado autor independente das variáveis na forma de citação do seu nome.
A elaboração do projeto do RI do IPEN foi iniciado em novembro de 2013, colocado em operação interna em julho de 2014 e disponibilizado na Internet em junho de 2015. Utiliza o software livre Dspace, desenvolvido pelo Massachusetts Institute of Technology (MIT). Para descrição dos metadados adota o padrão Dublin Core. É compatível com o Protocolo de Arquivos Abertos (OAI) permitindo interoperabilidade com repositórios de âmbito nacional e internacional.
1. Portaria IPEN-CNEN/SP nº 387, que estabeleceu os princípios que nortearam a criação do RDI,
clique aqui.
2. A experiência do Instituto de Pesquisas Energéticas e Nucleares (IPEN-CNEN/SP) na criação de um Repositório Digital Institucional – RDI,
clique aqui.
O Repositório Digital do IPEN é um equipamento institucional de acesso aberto, criado com o objetivo de reunir, preservar, disponibilizar e conferir maior visibilidade à Produção Científica publicada pelo Instituto, desde sua criação em 1956.
Operando, inicialmente como uma base de dados referencial o Repositório foi disponibilizado na atual plataforma, em junho de 2015. No Repositório está disponível o acesso ao conteúdo digital de artigos de periódicos, eventos, nacionais e internacionais, livros, capítulos, dissertações, teses e relatórios técnicos.
A elaboração do projeto do RI do IPEN foi iniciado em novembro de 2013, colocado em operação interna em julho de 2014 e disponibilizado na Internet em junho de 2015. Utiliza o software livre Dspace, desenvolvido pelo Massachusetts Institute of Technology (MIT). Para descrição dos metadados adota o padrão Dublin Core. É compatível com o Protocolo de Arquivos Abertos (OAI) permitindo interoperabilidade com repositórios de âmbito nacional e internacional.
O gerenciamento do Repositório está a cargo da Biblioteca do IPEN. Constam neste RI, até o presente momento 20.950 itens que tanto podem ser artigos de periódicos ou de eventos nacionais e internacionais, dissertações e teses, livros, capítulo de livros e relatórios técnicos. Para participar do RI-IPEN é necessário que pelo menos um dos autores tenha vínculo acadêmico ou funcional com o Instituto. Nesta primeira etapa de funcionamento do RI, a coleta das publicações é realizada periodicamente pela equipe da Biblioteca do IPEN, extraindo os dados das bases internacionais tais como a Web of Science, Scopus, INIS, SciElo além de verificar o Currículo Lattes. O RI-IPEN apresenta também um aspecto inovador no seu funcionamento. Por meio de metadados específicos ele está vinculado ao sistema de gerenciamento das atividades do Plano Diretor anual do IPEN (SIGEPI). Com o objetivo de fornecer dados numéricos para a elaboração dos indicadores da Produção Cientifica Institucional, disponibiliza uma tabela estatística registrando em tempo real a inserção de novos itens. Foi criado um metadado que contém um número único para cada integrante da comunidade científica do IPEN. Esse metadado se transformou em um filtro que ao ser acionado apresenta todos os trabalhos de um determinado autor independente das variáveis na forma de citação do seu nome.