JavaScript is disabled for your browser. Some features of this site may not work without it.
Navegação Eventos - Artigos por autor "ABE, ALFREDO"
-
GIOVEDI, CLAUDIA; ABE, ALFREDO
; MUNIZ, RAFAEL O.R.
; GOMES, DANIEL S.
; SILVA, ANTONIO T. e
; MARTINS, MARCELO R..
Analysis of the combined effects on the fuel performance of UO2-BeO as fuel and iron-based alloy as cladding.
In: WATER REACTOR FUEL PERFORMANCE MEETING,
September 10-14, 2017,
Jeju Island, Korea.
Proceedings...
2017.
p. 1-9.
Abstract:
Iron-based alloys have been considered as promising candidate material to replace zirconium-based alloys
as fuel cladding based on the previous experience of the first generation of pressurized water reactors (PWR). Moreover,
the safety margins of nuclear fuels can be improved by means of additives in the fuel pellet, as beryllium oxide (BeO), due
to the increase of the fuel thermal conductivity. These efforts are part of the accident tolerant fuel (ATF) program which
aims to develop nuclear fuel systems with enhanced performance under normal operation, design-basis accident and
severe-accident conditions. This paper addresses the combined effects on the fuel performance considering the BeO
additive in the fuel pellet and stainless steel 348 as cladding material under steady-state and loss-of-coolant-accident
(LOCA) scenario. The fuel performance simulation and assessment are conducted using modified versions of well-known
fuel performance codes (FRAPCON/FRAPTRAN). The obtained results have shown that the studied fuel system (stainless
steel cladding and UO2-BeO) enables an improvement in the main parameters associated to the fuel safety margins under
steady-state irradiation as well as LOCA scenario.
GIOVEDI, CLAUDIA; ABE, ALFREDO; MUNIZ, RAFAEL O.R.; GOMES, DANIEL S.; SILVA, ANTONIO T. e; MARTINS, MARCELO R.
Analysis of the combined effects on the fuel performance of UO2-BeO as fuel and iron-based alloy as cladding.
In:
WATER REACTOR FUEL PERFORMANCE MEETING,
September 10-14, 2017,
Jeju Island, Korea.
Proceedings...
2017.
p. 1-9.
Disponível em: http://repositorio.ipen.br/handle/123456789/29131. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
MUNIZ, RAFAEL O.R.
; GIOVEDI, CLAUDIA; ABE, ALFREDO
; GOMES, DANIEL S.
; AGUIAR, AMANDA A.; SILVA, ANTONIO T.
.
Assessment of uranium dioxide fuel performance with the addition of beryllium oxide.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Abstract:
The Fukushima Daiichi accident in 2011 pointed the problem related to the hydrogen generation under accident
scenarios due to the oxidation of zirconium-based alloys widely used as fuel rod cladding in water-cooled
reactors. This problem promoted research programs aiming the development of accident tolerant fuels (ATF)
which are fuels that under accident conditions could keep longer its integrity enabling the mitigation of the
accident effects. In the framework of the ATF program, different materials have been studied to be applied as
cladding to replace zirconium-based alloy; also efforts have been made to improve the uranium dioxide thermal
conductivity doping the fuel pellet. This paper evaluates the addition of beryllium oxide (BeO) to the uranium
dioxide in order to enhance the thermal conductivity of the fuel pellet. Investigations performed in this area
considering the addition of 10% in volume of BeO, resulting in the UO2-BeO fuel, have shown good results
with the improvement of the fuel thermal conductivity and the consequent reduction of the fuel temperatures
under irradiation. In this paper, two models obtained from open literature for the thermal conductivity of UO2-
BeO fuel were implemented in the FRAPCON 3.5 code and the results obtained using the modified code
versions were compared. The simulations were carried out using a case available in the code documentation
related to a typical pressurized water reactor (PWR) fuel rod irradiated under steady state condition. The results
show that the fuel centerline temperatures decrease with the addition of BeO, when compared to the
conventional UO2 pellet, independent of the model applied.
Palavras-Chave:
beryllium oxides;
comparative evaluations;
computerized simulation;
f codes;
fuel pellets;
fuel rods;
nuclear fuels;
performance;
pwr type reactors;
steady-state conditions;
thermal conductivity;
uranium dioxide
MUNIZ, RAFAEL O.R.; GIOVEDI, CLAUDIA; ABE, ALFREDO; GOMES, DANIEL S.; AGUIAR, AMANDA A.; SILVA, ANTONIO T.
Assessment of uranium dioxide fuel performance with the addition of beryllium oxide.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/28186. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO
; FUGA, RINALDO
; SANTOS, ADIMIR dos
; ANDRADE e SILVA, GRACIETE S. de
; FANARO, LEDA C.C.B.
; YAMAGUCHI, MITSUO
; JEREZ, ROGERIO
.
Critical loading configurations of the IPEN/MB-01 reactor with UOsub(2)GDsun(2)Osub(3) burnable poison rods.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 9th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 16th; MEETING ON NUCLEAR INDUSTRY, 1st,
September 27 - October 2, 2009,
Rio de Janeiro, RJ.
Proceedings...
Sao Paulo: ABEN, 2009,
2009.
Palavras-Chave:
burnable poisons;
control rod drives;
experimental data;
fuel rods;
gadolinium oxides;
ipen-mb-1 reactor;
k codes;
m codes;
monte carlo method;
multiplication factors;
reactor cores;
uranium dioxide
ABE, ALFREDO; FUGA, RINALDO; SANTOS, ADIMIR dos; ANDRADE e SILVA, GRACIETE S. de; FANARO, LEDA C.C.B.; YAMAGUCHI, MITSUO; JEREZ, ROGERIO.
Critical loading configurations of the IPEN/MB-01 reactor with UOsub(2)GDsun(2)Osub(3) burnable poison rods.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 9th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 16th; MEETING ON NUCLEAR INDUSTRY, 1st,
September 27 - October 2, 2009,
Rio de Janeiro, RJ.
Proceedings...
Sao Paulo: ABEN, 2009,
2009.
Disponível em: http://repositorio.ipen.br/handle/123456789/16612. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
PIOVEZAN, PAMELA; ABE, ALFREDO
; CARLUCCIO, THIAGO; SANTOS, ADIMIR dos
.
Heavy steel reflector evaluation using diffusion theory.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 11th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 18th; MEETING ON NUCLEAR INDUSTRY, 3rd,
November 24-29, 2013,
Recife, PE.
Proceedings...
Sao Paulo: ABEN, 2013,
2013.
Palavras-Chave:
absorption;
c codes;
cross sections;
distribution;
eigenvalues;
h codes;
ipen-mb-1 reactor;
neutron flux;
neutron reflectors;
performance;
reactor cores;
stainless steels;
PIOVEZAN, PAMELA; ABE, ALFREDO; CARLUCCIO, THIAGO; SANTOS, ADIMIR dos.
Heavy steel reflector evaluation using diffusion theory.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 11th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 18th; MEETING ON NUCLEAR INDUSTRY, 3rd,
November 24-29, 2013,
Recife, PE.
Proceedings...
Sao Paulo: ABEN, 2013,
2013.
Disponível em: http://repositorio.ipen.br/handle/123456789/17204. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
GIOVEDI, CLAUDIA; ABE, ALFREDO
; MUNIZ, RAFAEL O.R.
; GOMES, DANIEL de S.
; SILVA, ANTONIO T. e
; MARTINS, MARCELO R..
Modification of fuel performance code to evaluate iron-based alloy behavior under loca scenario.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Abstract:
Accident tolerant fuels (ATF) has been studied since the Fukushima Daiichi accident in the research efforts to
develop new materials which under accident scenarios could maintain the fuel rod integrity for a longer period
compared to the cladding and fuel system usually utilized in Pressurized Water Reactors (PWR). The efforts
have been focused on new materials applied as cladding, then iron-base alloys appear as a possible candidate.
The aim of this paper is to implement modifications in a fuel performance code to evaluate the behavior of ironbased
alloys under Loss-of-Coolant Accident (LOCA) scenario. For this, initially the properties related to the
thermal and mechanical behavior of iron-based alloys were obtained from the literature, appropriately adapted
and introduced in the fuel performance code subroutines. The adopted approach was step by step modifications,
where different versions of the code were created. The assessment of the implemented modification was carried
out simulating an experiment available in the open literature (IFA-650.5) related to zirconium-based alloy fuel
rods submitted to LOCA conditions. The obtained results for the iron-based alloy were compared to those
obtained using the regular version of the fuel performance code for zircaloy-4. The obtained results have shown
that the most important properties to be changed are those from the subroutines related to the mechanical
properties of the cladding. The results obtained have shown that the burst is observed at a longer time for fuel
rods with iron-based alloy, indicating the potentiality of this material to be used as cladding with ATF purposes.
Palavras-Chave:
accident-tolerant nuclear fuels;
cladding;
computerized simulation;
f codes;
fuel rods;
iron alloys;
loss of coolant;
performance;
pwr type reactors;
stainless steel-348
GIOVEDI, CLAUDIA; ABE, ALFREDO; MUNIZ, RAFAEL O.R.; GOMES, DANIEL de S.; SILVA, ANTONIO T. e; MARTINS, MARCELO R.
Modification of fuel performance code to evaluate iron-based alloy behavior under loca scenario.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/28187. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
SANCHEZ, ANDREA; ABE, ALFREDO
.
Nuclear criticality safety parameter evaluation for uranium metallic alloy.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 11th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 18th; MEETING ON NUCLEAR INDUSTRY, 3rd,
November 24-29, 2013,
Recife, PE.
Proceedings...
Sao Paulo: ABEN, 2013,
2013.
Palavras-Chave:
uranium alloys;
nuclear fuels;
criticality;
safety analysis;
s codes;
monte carlo method
SANCHEZ, ANDREA; ABE, ALFREDO.
Nuclear criticality safety parameter evaluation for uranium metallic alloy.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 11th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 18th; MEETING ON NUCLEAR INDUSTRY, 3rd,
November 24-29, 2013,
Recife, PE.
Proceedings...
Sao Paulo: ABEN, 2013,
2013.
Disponível em: http://repositorio.ipen.br/handle/123456789/17324. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO
; CARLUCCIO, THIAGO; PIOVEZAN, PAMELA; GIOVEDI, CLAUDIA; MARTINS, MARCELO.
Preliminary neutronic assessmento for ATF (Accident Tolerant Fuel) based on iron alloy.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Palavras-Chave:
fuel rods;
cladding;
iron alloys;
loss of coolant;
monte carlo method;
neutron absorbers;
nuclear fuels;
pwr type reactors;
tolerance;
zirconium alloys
ABE, ALFREDO; CARLUCCIO, THIAGO; PIOVEZAN, PAMELA; GIOVEDI, CLAUDIA; MARTINS, MARCELO.
Preliminary neutronic assessmento for ATF (Accident Tolerant Fuel) based on iron alloy.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Disponível em: http://repositorio.ipen.br/handle/123456789/24029. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO
; SANCHEZ, ANDREA; YAMAGUCHI, MITSUO
; FUGA, RINALDO.
Reactivity experiments with different boric acid concentrations in the IPEN/MB-01 reactor.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 10th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 17th; MEETING ON NUCLEAR INDUSTRY, 2nd,
October 24-28, 2011,
Belo Horizonte, MG.
Proceedings...
São Paulo: ABEN, 2011,
2011.
Palavras-Chave:
ipen-mb-1 reactor;
reactor cores;
boric acid;
monte carlo method
ABE, ALFREDO; SANCHEZ, ANDREA; YAMAGUCHI, MITSUO; FUGA, RINALDO.
Reactivity experiments with different boric acid concentrations in the IPEN/MB-01 reactor.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 10th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 17th; MEETING ON NUCLEAR INDUSTRY, 2nd,
October 24-28, 2011,
Belo Horizonte, MG.
Proceedings...
São Paulo: ABEN, 2011,
2011.
Disponível em: http://repositorio.ipen.br/handle/123456789/16161. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO
; GIOVEDI, CLAUDIA; GOMES, DANIEL
; SILVA, ANTONIO T. e
; MUNIZ, RAFAEL O.R.
; MARTINS, MARCELO.
Sensitivity assessment of fuel performance codes for loca accident scenario.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Abstract:
FRAPCON code predicts fuel rod performance in LWR (Light Water Reactor) by modeling fuel responses under normal operating conditions and anticipated operational occurrences; FRAPTRAN code is applied for fuel transient under fast transient and accident conditions. The codes are well known and applied for different purposes and one of the use is to address sensitivity analysis considering fuel design parameters associated to fabrication, moreover can address the effect of physical models bias. The objective of this work was to perform an assessment of fuel manufacturing parameters tolerances and fuel models bias using FRAPCON and FRAPTRAN codes for Loss of Coolant Accident (LOCA) scenario. The preliminary analysis considered direct approach taken into account most relevant manufacturing tolerances (lower and upper bounds) related to design parameters and physical models bias without considering their statistical distribution. The simulations were carried out using the data available in the open literature related to the series of LOCA experiment performed at the Halden reactor (specifically IFA-650.5). The manufacturing tolerances associated to design parameters considered in this paper were: enrichment, cladding thickness, pellet diameter, pellet density, and filling gas pressure. The physical models considered were: fuel thermal expansion, fission gas release, fuel swelling, irradiation creep, cladding thermal expansion, cladding corrosion, and cladding hydrogen pickup. The results obtained from sensitivity analysis addressed the impact of manufacturing tolerances and physical models in the fuel cladding burst time observed for the IFA-650.5 experiment.
Palavras-Chave:
accident-tolerant nuclear fuels;
computerized simulation;
f codes;
fuel rods;
fuel-cladding interactions;
loss of coolant;
sensitivity analysis;
transients;
water cooled reactors
ABE, ALFREDO; GIOVEDI, CLAUDIA; GOMES, DANIEL; SILVA, ANTONIO T. e; MUNIZ, RAFAEL O.R.; MARTINS, MARCELO.
Sensitivity assessment of fuel performance codes for loca accident scenario.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE,
October 22-27, 2017,
Belo Horizonte, MG.
Proceedings...
Rio de Janeiro, RJ: Associação Brasileira de Energia Nuclear,
2017.
Disponível em: http://repositorio.ipen.br/handle/123456789/28196. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
GOMES, DANIEL de S.
; TEIXEIRA e SILVA, ANTONIO
; ABE, ALFREDO
; GIOVEDI, CLAUDIA; MARTINS, MARCELO R..
Simulation of the effects of the extend fuel rod burn-up under loca scenario.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Palavras-Chave:
simulation;
fuel rods;
burnup;
loss of coolant;
f codes;
comparative evaluations
GOMES, DANIEL de S.; TEIXEIRA e SILVA, ANTONIO; ABE, ALFREDO; GIOVEDI, CLAUDIA; MARTINS, MARCELO R.
Simulation of the effects of the extend fuel rod burn-up under loca scenario.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 12th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 19th; MEETING ON NUCLEAR INDUSTRY, 4th,
October 4-9, 2015,
São Paulo, SP.
Proceedings...
2015.
Disponível em: http://repositorio.ipen.br/handle/123456789/25154. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO; SANCHEZ, ANDREA; YAMAGUCHI, MITSUO
.
The evaluation of set of criticality parameters using scale system.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 9th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 16th; MEETING ON NUCLEAR INDUSTRY, 1st,
September 27 - October 2, 2009,
Rio de Janeiro, RJ.
Proceedings...
Sao Paulo: ABEN, 2009,
2009.
Palavras-Chave:
criticality;
cross sections;
m codes;
monte carlo method;
multiplication factors;
nuclear data collections;
numerical data;
s codes;
uranium 235
ABE, ALFREDO; SANCHEZ, ANDREA; YAMAGUCHI, MITSUO.
The evaluation of set of criticality parameters using scale system.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 9th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 16th; MEETING ON NUCLEAR INDUSTRY, 1st,
September 27 - October 2, 2009,
Rio de Janeiro, RJ.
Proceedings...
Sao Paulo: ABEN, 2009,
2009.
Disponível em: http://repositorio.ipen.br/handle/123456789/16613. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
-
ABE, ALFREDO
; SANTOS, ADIMIR dos
; FUGA, RINALDO
.
A variable reflector size experiment at IPEN/MB-01 critical facility.
In: INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 10th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 17th; MEETING ON NUCLEAR INDUSTRY, 2nd,
October 24-28, 2011,
Belo Horizonte, MG.
Proceedings...
São Paulo: ABEN, 2011,
2011.
Palavras-Chave:
ipen-mb-1 reactor;
reactor cores;
neutron reflectors;
size;
aluminium;
control rooms
ABE, ALFREDO; SANTOS, ADIMIR dos; FUGA, RINALDO.
A variable reflector size experiment at IPEN/MB-01 critical facility.
In:
INTERNATIONAL NUCLEAR ATLANTIC CONFERENCE; MEETING ON NUCLEAR APPLICATIONS, 10th; MEETING ON REACTOR PHYSICS AND THERMAL HYDRAULICS, 17th; MEETING ON NUCLEAR INDUSTRY, 2nd,
October 24-28, 2011,
Belo Horizonte, MG.
Proceedings...
São Paulo: ABEN, 2011,
2011.
Disponível em: http://repositorio.ipen.br/handle/123456789/16158. Acesso em: $DATA.
Esta referência é gerada automaticamente de acordo com as normas do estilo IPEN/SP (ABNT NBR 6023) e recomenda-se uma verificação final e ajustes caso necessário.
Como referenciar este item
Buscar no repositório
Navegar
-
Todo o repositório
-
Esta coleção
Minha conta
Visualizar
A pesquisa no RD utiliza os recursos de busca da maioria das bases de dados. No entanto algumas dicas podem auxiliar para obter um resultado mais pertinente.
✔ É possível efetuar a busca de um autor ou um termo em todo o RD, por meio do
Buscar no Repositório
, isto é, o termo solicitado será localizado em qualquer campo do RD. No entanto esse tipo de pesquisa não é recomendada a não ser que se deseje um resultado amplo e generalizado.
✔ A pesquisa apresentará melhor resultado selecionando um dos filtros disponíveis em
Navegar
✔ Os filtros disponíveis em
Navegar
tais como: Coleções, Ano de publicação, Títulos, Assuntos, Autores, Revista, Tipo de publicação são autoexplicativos. O filtro,
Autores IPEN
apresenta uma relação com os autores vinculados ao IPEN; o
ID Autor IPEN
diz respeito ao número único de identificação de cada autor constante no RD e sob o qual estão agrupados todos os seus trabalhos independente das variáveis do seu nome;
Tipo de acesso
diz respeito à acessibilidade do documento, isto é , sujeito as leis de direitos autorais, ID RT apresenta a relação dos relatórios técnicos, restritos para consulta das comunidades indicadas.
A opção
Busca avançada
utiliza os conectores da lógica boleana, é o melhor recurso para combinar chaves de busca e obter documentos relevantes à sua pesquisa, utilize os filtros apresentados na caixa de seleção para refinar o resultado de busca. Pode-se adicionar vários filtros a uma mesma busca.
Exemplo:
Buscar os artigos apresentados em um evento internacional de 2015, sobre loss of coolant, do autor Maprelian.
Autor: Maprelian
Título: loss of coolant
Tipo de publicação: Texto completo de evento
Ano de publicação: 2015
✔ Para indexação dos documentos é utilizado o Thesaurus do INIS, especializado na área nuclear e utilizado em todos os países membros da
International Atomic Energy Agency – IAEA
, por esse motivo, utilize os termos de busca de assunto em inglês; isto não exclui a busca livre por palavras, apenas o resultado pode não ser tão relevante ou pertinente.
✔ 95% do RD apresenta o texto completo do documento com livre acesso, para aqueles que apresentam o
significa que e o documento está sujeito as leis de direitos autorais, solicita-se nesses casos contatar a Biblioteca do IPEN,
bibl@ipen.br
.
✔ Ao efetuar a busca por um autor o RD apresentará uma relação de todos os trabalhos depositados no RD. No lado direito da tela são apresentados os coautores com o número de trabalhos produzidos em conjunto bem como os assuntos abordados e os respectivos anos de publicação agrupados.
✔ O RD disponibiliza um quadro estatístico de produtividade, onde é possível visualizar o número dos trabalhos agrupados por tipo de coleção, a medida que estão sendo depositados no RD.
✔ Na página inicial nas referências são sinalizados todos os autores IPEN, ao clicar nesse símbolo
será aberta uma nova página correspondente à aquele autor – trata-se da página do pesquisador.
✔ Na página do pesquisador, é possível verificar, as variações do nome, a relação de todos os trabalhos com texto completo bem como um quadro resumo numérico; há links para o Currículo Lattes e o Google Acadêmico ( quando esse for informado).
ATENÇÃO!
ESTE TEXTO "AJUDA" ESTÁ SUJEITO A ATUALIZAÇÕES CONSTANTES, A MEDIDA QUE NOVAS FUNCIONALIDADES E RECURSOS DE BUSCA FOREM SENDO DESENVOLVIDOS PELAS EQUIPES DA BIBLIOTECA E DA INFORMÁTICA.
O gerenciamento do Repositório está a cargo da Biblioteca do IPEN. Constam neste RI, até o presente momento 20.950 itens que tanto podem ser artigos de periódicos ou de eventos nacionais e internacionais, dissertações e teses, livros, capítulo de livros e relatórios técnicos. Para participar do RI-IPEN é necessário que pelo menos um dos autores tenha vínculo acadêmico ou funcional com o Instituto. Nesta primeira etapa de funcionamento do RI, a coleta das publicações é realizada periodicamente pela equipe da Biblioteca do IPEN, extraindo os dados das bases internacionais tais como a Web of Science, Scopus, INIS, SciElo além de verificar o Currículo Lattes. O RI-IPEN apresenta também um aspecto inovador no seu funcionamento. Por meio de metadados específicos ele está vinculado ao sistema de gerenciamento das atividades do Plano Diretor anual do IPEN (SIGEPI). Com o objetivo de fornecer dados numéricos para a elaboração dos indicadores da Produção Cientifica Institucional, disponibiliza uma tabela estatística registrando em tempo real a inserção de novos itens. Foi criado um metadado que contém um número único para cada integrante da comunidade científica do IPEN. Esse metadado se transformou em um filtro que ao ser acionado apresenta todos os trabalhos de um determinado autor independente das variáveis na forma de citação do seu nome.
A elaboração do projeto do RI do IPEN foi iniciado em novembro de 2013, colocado em operação interna em julho de 2014 e disponibilizado na Internet em junho de 2015. Utiliza o software livre Dspace, desenvolvido pelo Massachusetts Institute of Technology (MIT). Para descrição dos metadados adota o padrão Dublin Core. É compatível com o Protocolo de Arquivos Abertos (OAI) permitindo interoperabilidade com repositórios de âmbito nacional e internacional.
1. Portaria IPEN-CNEN/SP nº 387, que estabeleceu os princípios que nortearam a criação do RDI,
clique aqui.
2. A experiência do Instituto de Pesquisas Energéticas e Nucleares (IPEN-CNEN/SP) na criação de um Repositório Digital Institucional – RDI,
clique aqui.
O Repositório Digital do IPEN é um equipamento institucional de acesso aberto, criado com o objetivo de reunir, preservar, disponibilizar e conferir maior visibilidade à Produção Científica publicada pelo Instituto, desde sua criação em 1956.
Operando, inicialmente como uma base de dados referencial o Repositório foi disponibilizado na atual plataforma, em junho de 2015. No Repositório está disponível o acesso ao conteúdo digital de artigos de periódicos, eventos, nacionais e internacionais, livros, capítulos, dissertações, teses e relatórios técnicos.
A elaboração do projeto do RI do IPEN foi iniciado em novembro de 2013, colocado em operação interna em julho de 2014 e disponibilizado na Internet em junho de 2015. Utiliza o software livre Dspace, desenvolvido pelo Massachusetts Institute of Technology (MIT). Para descrição dos metadados adota o padrão Dublin Core. É compatível com o Protocolo de Arquivos Abertos (OAI) permitindo interoperabilidade com repositórios de âmbito nacional e internacional.
O gerenciamento do Repositório está a cargo da Biblioteca do IPEN. Constam neste RI, até o presente momento 20.950 itens que tanto podem ser artigos de periódicos ou de eventos nacionais e internacionais, dissertações e teses, livros, capítulo de livros e relatórios técnicos. Para participar do RI-IPEN é necessário que pelo menos um dos autores tenha vínculo acadêmico ou funcional com o Instituto. Nesta primeira etapa de funcionamento do RI, a coleta das publicações é realizada periodicamente pela equipe da Biblioteca do IPEN, extraindo os dados das bases internacionais tais como a Web of Science, Scopus, INIS, SciElo além de verificar o Currículo Lattes. O RI-IPEN apresenta também um aspecto inovador no seu funcionamento. Por meio de metadados específicos ele está vinculado ao sistema de gerenciamento das atividades do Plano Diretor anual do IPEN (SIGEPI). Com o objetivo de fornecer dados numéricos para a elaboração dos indicadores da Produção Cientifica Institucional, disponibiliza uma tabela estatística registrando em tempo real a inserção de novos itens. Foi criado um metadado que contém um número único para cada integrante da comunidade científica do IPEN. Esse metadado se transformou em um filtro que ao ser acionado apresenta todos os trabalhos de um determinado autor independente das variáveis na forma de citação do seu nome.